#DIY PLUMB BOB HOW TO#
#DIY PLUMB BOB INSTALL#
#DIY PLUMB BOB FREE#

Insert the corner-groove weather stripping into the channels.

Use the corner-grooving tool to cut into the corners on all sides of the jamb.

Tie a knot in the string on the side that will sit inside the cap. If your plumb-bob does not have a screw cap then simply tie the string around the hole at the top. Step 1 Unscrew cap and feed string through hole.

#DIY PLUMB BOB HOW TO#

To make the filler pieces blend in with the rest of the door, use a utility knife and a speed square to extend score marks from the door to the filler pieces. How to replace the string on a plumb-bob.

Give the filler pieces on the door a good sanding with the palm sander.

Once the glue is dry, cut the door to length and width using the track saw.

All you need is some kind of weight, like a nut, bolt.

Clamp everything together and allow the glue to dry. If you dont have a plumb bob, you can easily make one using a weight and a piece of string.

Follow the instructions provided with the weather stripping to screw in the mounting bracket and slide in the weather stripping.

#DIY PLUMB BOB INSTALL#

Instead of filling the gap in the middle, install automatic weather stripping to ensure a tight seal.Attach two pieces of 1×6″ lumber to the rabbeted door using wood glue.To make the door the correct length, make two rabbet cuts on each side of the bottom of the door.Drill new holes for the hinges and screw them back into the jamb.Chisel out a new mortise for the door hinge based on the mark from the scribe.Use the scribe to measure the distance between the hinge and other end of the door, and transfer that measurement to the jamb by holding the scribe against the new stop just chiseled out.Repeat this process on the jamb on the other side of the door.Keep an eye out for any other nails that might have been missed to protect the chisel from being damaged. Smooth it out with a planer and a palm sander. Replace the cap on the weighted and pointed. Pull the remaining string through the plumb bob top until the knot sits inside the removable cap. Tie a double knot in the end of the string. The line should be at least the height from floor to ceiling 8 feet is typical. Chisel out any wood that lies outside the chalk line on the jamb. Feed the plumb bob dry line or string through the hole in the removable top.Put the other end of the chalk line at the other end of the jamb inward by the difference between the two measurements. To make the door plumb, hold a chalk line at the edge of the jamb on the end of the door that had the larger measurement.Use a measuring tape to determine if there’s a difference between the distance of the plumb bob string at the top of the door and the distance from the string to the bottom of the door.Attach the plumb bob to the top of the door and pull the weight to the bottom of the door.Some bobs have pointed tips that can be bent by repeated use or abuse if the point on yours is bent or out of alignment, replace it.3-4 hours Steps for fitting an antique door

Excavation and foundation contractors rely upon the plumb line, and constructing a chimney the tool can indicate whether a flue is running true vertical or veering off plumb.

Surveyors sometimes use plumb bobs for lining up points or transferring them. The plumb line in one place can be used to sight an object in another - a pipe, for example - for plumb. Once it is hung and still, the top and bottom points can be marked and used as guides. For example, you can locate fixtures or decorations in relation to an object or surface below (or above) using the plumb line. A spirit level will also accomplish those tasks, but some jobs are much more easily done using the tool.

The plumb bob is useful in establishing vertical for a wall in construction or a doorjamb when hanging a door.

#DIY PLUMB BOB FREE#

(Note that the line must be hanging free to get an accurate reading.) The weight, or bob, is then allowed to swing freely when it stops, the point of the bob is precisely below the point at which the string is fixed above. To use the tool, the string is fixed at the point to be plumbed.

Diy plumb bob